Electronic Ignition Conversion Pleasurecraft Marine 8-Cyl Prestolite Distributor

Description

Electronic Ignition Conversion Kits for 8-Cylinder Prestolite Distributors with Screw-Down Cap
Electronic Ignition Conversion Kit
for
Prestolite 8-Cylinder Marine Applications
for 8-cylinder, Non-Vacuum-Advance Prestolite Distributors
Replaces Points and Condenser - Never Adjust Points or Timing Again!
The
Hot-Spark
electronic ignition conversion kit replaces breaker points and condenser in the distributor to provide rock-solid reliability. With the
Hot-Spark
electronic ignition, dwell and timing are always
spot-on
accurate.
No matter how strong your engine is, you won't get the most out of it without a good spark. The stock, points-based ignition system used technology that dates back a century - to the Kettering system, which was introduced in the 1910 Cadillac. Even though you can adjust breaker points for near-electronic ignition performance, they will burn and wear within a few thousand miles, long before the recommended replacement interval. With points, the timing will drift; power and fuel economy will suffer.
The
Hot-Spark
electronic ignition conversion kit delivers a strong spark every time and is maintenance-free. You'll notice quicker starts, more top end power and a little gas mileage boost. It's as easy to install as points and condenser!
Advantages of the
Hot-Spark
electronic ignition conversion kit:
Replaces points and condenser with solid-state electronics
Set it and forget it - Never adjust points and timing again!
Zero maintenance
Delivers far more voltage to the spark plugs than points-based points
Reliable Hall-effect technology
Never gets out of adjustment
Rock-steady reliability
Dwell and timing are always spot-on accurate
Increased gas mileage, fuel economy
Quick starting
Smooth idling
Cleaner emissions
Longer spark plug life
Longer engine life
Cleaner engine oil due to less unburned fuel
Longer interval between oil changes
Easy to install - If you can install points, you can install the Hot-Spark electronic ignition conversion
No points to wear, burn, pit or corrode
No condenser needed
Absolutely no points float - zero - even at redline RPM and beyond!
Never worry about drifting dwell or timing again
No rubbing parts - nothing to wear out!
Fits completely under the distributor cap
Stealth modification - maintains stock appearance
Includes everything you need, no external ignition box required.
Works with stock distributor and coil
Encased in high-temp thermoplastic - protected from the elements and oil, grease, dirt, water, etc.
Never bother with points or condenser again!
The best investment you'll ever make for your vehicle
Saves precious ($$$) fuel
Coil with 1.5 Ohms or more internal, primary resistance required.
Requires a 12-volt, negative ground electrical system.
External Ballast Resistor: If the charging system voltage, measured at the coil's + terminal, is more than 13.9 volts at any RPM level, the voltage regulator likely needs replacing or a
1.4 Ohm ballast resistor
should be wired between the coil's + terminal and the red HotSpark ignition wire. Too much voltage can damage the ignition module and other electronic components.
How many miles until the Hot-Spark electronic ignition conversion kit pays for itself? Click
here
Measuring Coil Resistance (and more):
www.Hot-Spark.com/Coil.htm
Prestolite distributors must have the original breaker plate, complete with with points and condenser, in order for the 3PRE8U1/3PRE8U2 ignition conversion kit to fit.
3PRE6U2
- For 6-cylinder Prestolite Non-Vacuum-Advance Distributor with Screw-down Distributor Cap
3PRE8U1
- For 8-Cylinder Prestolite Non-Vacuum-Advance Distributor with Clip-down Distributor Cap
3PRE8U2
- For 8-Cylinder Prestolite Non-Vacuum-Advance Distributor with Screw-down Distributor Cap
For
Prestolite 8-Cylinder Marine
Distributors
Must be used with stock Prestolite distributor breaker points plate. Prestolite distributors must have the original breaker plate, complete with with points and condenser, in order for the 3PRE8U1/3PRE8U2 ignition conversion kit to fit.
Chevrolet Marine
1976-88 8-cyl All models IBM-7011 Prestolite - 3PRE8U1
1976-88 8-cyl All models IBM-7013 Prestolite - 3PRE8U2
Chris-Craft
1963-71 8-cyl All models IBM-4115, IBM-4116 Prestolite - 3PRE8U1
1981-85 8-cyl All models   IBM-7013 Prestolite - 3PRE8U2
Chrysler Inboard
1959-72 8-cyl M80, M81, M318A, B, C, M413, D, M426X  IBM-4106 Prestolite - 3PRE8U1
1965-66 8-cyl M318X   IBM-4120 Prestolite - 3PRE8U1
1983-88 8-cyl 273, 318, 340, 440 engine IBM-7016, IBM-7017 Prestolite - 3PRE8U2
Crusader (Thermo-Electron)
1961-69 8-cyl 283,327, 409,   IBM-4110 Prestolite - 3PRE8U1
1975-78 8-cyl 302 cid. engine IBM-7007, IBM-7007A Prestolite - 3PRE8U1
1977-82 8-cyl 305, 350, 454 cid. engine IBM-7011, IBM-7011C, IBM-7011D; Prestolite - 3PRE8U1
Dearborn Marine
1966-69 8-cyl 260, 289, 302  Motorcraft - 3FOR8U1
Ford - (Interceptor)
1973-88 8-cyl 302, 351, 460 cid. engine   IBM-7007, IBM-7008 Prestolite - 3PRE8U1
1973-88 8-cyl 302, 351, 460 cid. engine   IBM-7019, IBM-7020 Prestolite - 3PRE8U2
Indmar Products
1979 8-cyl All models Prestolite IBM-7011 - 3PRE8U1
Marine Power Systems
1978-83 8-cyl 305, 350, 454 cid. engine Prestolite IBM-7011 - 3PRE8U1
1978-83 8-cyl 305, 350, 454 cid. engine Prestolite IBM-7013 - 3PRE8U2
Mercruiser (Mercury Marine)
All 8-cyl 233 from Serial 4173000 Prestolite - 3PRE8U1
All 8-cyl 888, from Serial 3108723 Prestolite - 3PRE8U1
All 8-cyl 233, from Serial 4173000 Prestolite - 3PRE8U2
OMC
1974 8-cyl 170 HP Prestolite - 3PRE8U1
1979 8-cyl 250 HP Prestolite 981080 - 3PRE8U1
1975-77 8-cyl 175, 190 HP Prestolite 980902 - 3PRE8U1
1975-77 8-cyl 235HP Prestolite 981080 - 3PRE8U1
1975-79 8-cyl 240 HP Prestolite 981080 - 3PRE8U1
1978-80 8 185 HP Prestolite 982320 - 3PRE8U1
1979-82 8-cyl 260 HP Prestolite 982320 - 3PRE8U1
1979-88 8-cyl 200, 230 HP Prestolite 982320 - 3PRE8U1
1980-82 8-cyl 305, 350, 454 cid. engine Prestolite 982320 - 3PRE8U1
1982-88 8-cyl 5.0 liter, 5.7 liter Prestolite IBM-7013C, IBM-7013D - 3PRE8U2
1987-88 8-cyl 7.5 liter Prestolite - 3PRE8U2
Pleasurecraft
1975-78 8-cyl Ford 302 cid. engine   IBM-7007, A Prestolite - 3PRE8U1
1975-78 8-cyl Ford 351, 460 cid. engine   IBM-7008, IBM-7008A, IBM-7008B, IBM-7008C Prestolite - 3PRE8U1
1976-82 8-cyl 305, 350, 454 cid. engine   IBM-7011 Prestolite - 3PRE8U1
1983-88 8-cyl 305, 350, 454 cid. engine   IBM-7013 Prestolite - 3PRE8U2
Prestolite Distributors:
Prestolite 4-cyl IBM-7026  Marine Distributor, with screw-down distributor cap - 3PRE4U2
Prestolite 6-cyl Prestolite
IBM-7021  Marine Distributors - 3PRE6U2
1977-82 8-cyl All models Prestolite IBM-7011A Marine Distributors- 3PRE8U1
1977-82 8-cyl All models Prestolite IBM-7013A Distributors- 3PRE8U2
Teledyne Marine Co. (Gray Marine)
1965-68 8-cyl CF175, 195, CH175, 195   IBM-4119, IBM-4119A Prestolite - 3PRE8U1
Thermo-Electron
1977-82 8-cyl 305, 350, 454 cid. engine   IBM-7011D Prestolite - 3PRE8U1
1981-82 8-cyl 305, 350, 454 cid. engine   IBM-7013 Prestolite - 3PRE8U2
Volvo-Penta with Prestolite Distributors
4-cylinder Prestolite
IBM-7026 Marine Distributors - 3PRE4U2
6-cylinder Prestolite
IBM-7021 Marine Distributors - 3PRE6U2
1977-82 8-cyl All models Prestolite IBM-7011A Marine Distributors- 3PRE8U1
1977-82 8-cyl All models Prestolite IBM-7013A Marine Distributors- 3PRE8U2
CU-20460, CU-32023
- 3PRE8U2
Please note that SAE J1171 and UL 428D are NOT distributor part numbers,  but simply US government standards that many completely different distributors meet. These numbers are of almost no use in determining which distributor you have or what ignition kit you need.
Usually, the Prestolite distributor part number will be on the opposite side of the distributor body.
www.Hot-Spark.com/Installing-Hot-Spark-Prestolite.pdf
International Buyers – Please Note:
Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility.
Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying.
VERY IMPORTANT -- BEFORE ORDERING:
Some distributors of vehicles, boats, etc. may differ, according to whether the stock distributor is still in place or a replacement distributor has been installed. Some otherwise similar or identical engines use different distributor brands and/or different distributor part numbers. We need your distributor's brand name, distributor part number and number of engine cylinders to ensure that the electronic ignition conversion kit is correct one for your particular distributor.
If your distributor part number, normally found on the side of the distributor body, is not among those listed on the relevant web page, chances are, the HotSpark ignition conversion kit won't fit your distributor.
It's imperative that we know your distributor's brand name, distributor part number and the number of cylinders of your engine. You may need to remove the distributor temporarily, so that you can read the distributor part number from the side of the distributor body. Usually, the side of your distributor will be covered with oil and dirt, so you'll need to clean it to find the distributor brand name and exact part number.
We can guarantee only that each of our ignition kits will fit a distributor with one of the distributor part numbers listed on its relevant web page. Otherwise, it likely won't fit. HotSpark ignition kits require a 12-volt, negative ground (earth) electrical system.
If you order the wrong electronic ignition conversion kit for your distributor, you'll need to return it to us, via US Postal Service mail within 30 days from date of purchase. If the ignition kit is in perfect, unused condition, we can accept it as a retuned item, within 30 days of purchase, and provide a refund to your PayPal account, less a 20% restocking fee and any international shipping fees, etc., but only if the ignition kit is in pristine, unused condition. Buyer is responsible for shipping and other costs to return the product for credit or exchange.
3PRE8U1
Electronic Ignition Conversion Kit for 8-cylinder Prestolite Distributors without Vacuum Advance, with Clip-down Distributor Cap
Easy to Install -
Replace Points and Condenser
with
Solid-State Electronics
Electronic Ignition Conversion Kit. Replaces points and condenser in  8-cylinder Prestolite non-vacuum-advance distributors with clip-down distributor cap.
Application:
8-cylinder Prestolite non-vacuum-advance distributors. See application chart above. 12V negative ground only.
Prestolite 8-cylinder Distributors:
980902
981080
982320
IBM-4106
IBM-4110
IBM-4115
IBM-4116
IBM-4117A
IBM-4118A
IBM-4119
IBM-4120
IBM-7003
IBM-7003B
IBM-7003BS
IBM-7004
IBM-7004A
IBM-7004AS
IBM-7004B
IBM-7004BS
IBM-7007
IBM-7007A
IBM-7007AS
IBM-7007S
IBM-7008
IBM-7008A
IBM-7008AS
IBM-7008B
IBM-7008BS
IBM-7008C
IBM-7008CS
IBM-7008S
IBM-7011
IBM-7011A
IBM-7011C
IBM-7011D
IBM-4105
IBM-4105A
IBM-4106
IBM-4107
IBM-4107A
IBM-4108
IBM-4109
IBM-4110
IBM-4112
IBM-4115
IBM-4116
IBM-4117A
IBM-4119
IBM-4119A
IBM-4120
IBM-7003B
IBM-7003BS
IBM-7004A
IBM-7004AS
IBM-7004B
IBM-7004BS
IBM-7007
IBM-7007A
IBM-7007AS
IBM-7007S
IBM-7008
IBM-7008A
IBM-7008AS
IBM-7008B
IBM-7008BS
IBM-7008C
IBM-7008CS
IBM-7008S
IBM-7011
IBM-7011A
IBM-7011C
IBM-7011D
The 8-cylinder magnet sleeve fits Prestolite  distributor shaft cam lobes measuring 25mm from edge-to-edge.
12V negative ground only.
Coil Required:
Coil must have 1.5 Ohms or more primary resistance.
In stock:
Available:
Item Number: 3PRE8U1
Price: US .95
FREE SHIPPING
to anywhere in the USA
Item Name: Hot-Spark Electronic Ignition Conversion Kit for 8-cylinder Prestolite Distributors without vacuum advance, with clip-down distributor cap.
Includes everything you need - no external ignition box required.
Price: US .95
Price with Shipping
Shipped within USA .95 USD
Shipped to Other Countries 9.95 USD
3PRE8U2
Electronic Ignition Conversion Kit for 8-cylinder Prestolite Distributors without Vacuum Advance, with Screw-down Distributor Cap
Easy to Install -
Replace Points and Condenser
with
Solid-State Electronics
Electronic Ignition Conversion Kit. Replaces points and condenser in  8-cylinder Prestolite non-vacuum-advance distributors with screw-down distributor cap.
Application:
8-cylinder Prestolite non-vacuum-advance distributors. See application chart above. 12V negative ground only.
Prestolite 8-cylinder Distributors:
E5JL-12100CA
IBM-7012
IBM-7013
IBM-7013-9P
IBM-7013A
IBM-7013C
IBM-7013D
IBM-7013E
IBM-7016
IBM-7017
IBM-7019
IBM-7019A
IBM-7019AS
IBM-7019S
IBM-7020
IBM-7020A
IBM-7020AS
IBM-7020B
IBM-7020BS
IBM-7020C
IBM-7020CS
IBM-7020S
IBM-MARINE
The 8-cylinder magnet sleeve fits Prestolite  distributor shaft cam lobes measuring 23.75mm from edge-to-edge.
12V negative ground only.
Coil Required:
Coil must have 1.5 Ohms or more primary resistance.
In stock:
Available:
Item Number: 3PRE8U2
Price: US .95
FREE SHIPPING
to anywhere in the USA
Item Name: Hot-Spark Electronic Ignition Conversion Kit for 8-cylinder Prestolite Distributors without vacuum advance, with screw-down distributor cap.
Includes everything you need - no external ignition box required.
Price: US .95
Price with Shipping
Shipped within USA .95 USD
Shipped to Other Countries 9.95 USD
HS14BR
Hot-Spark 1.4 Ohm Heavy-Duty Ceramic External Ballast Resistor
1.4 Ohm Ballast Resistor - Ideal for Use with Electronic Ignition and High-Voltage Charging Systems
Also r
educes burning and pitting of contact breaker points.
1.4 Ohm heavy-duty, external ceramic ballast resistor - installed between coil's + terminal and condenser or HotSpark ignition's red wire. Lowers amperage to points or ignition module, ensuring trouble-free operation. Installed on engine firewall or on coil. Ideal for use with high-voltage charging systems and electronic ignition or points.
Application:
Recommended for use with high-voltage charging systems. Typically lowers current @ 3,000 RPM by about 0.5 amps.
Supplements original stock coil.
Also extends the life of points when used with points-based ignition systems. Reduces  burning and pitting of points.
In Stock:
Available:
Item Number: HS14BR
Price: US
5
.95
FREE SHIPPING to anywhere within the USA. Ships to USA only - no international shipping available for this item, unless ordered with distributor, coil or ignition kit.
Charging system voltage, measured at the coil’s + terminal, must never exceed 13.9 volts, at any RPM level. You can reduce over-amperage surges/voltage spikes to the ignition module by wiring a 1.4 Ohm ballast resistor between the coil's + terminal and the red HotSpark ignition module's red wire.
Price with Shipping
Shipped within USA .95 USD
Foreign Orders: Shipping discount available if purchasing multiple items.
Certain OMC engines with electronic shift assist may require the following wiring modifications:
www.hot-spark.com/OMC-Shift-Assist-Adapter.jpg
Dealer Inquiries
welcomed.
© 2005-2021 Hot Spark
®
1582  91582  1581  91581  18-5298  18-5299